This foot pedal machine can make incense sticks such as wormwood incense, perch incense, spiral incense, flower-shaped incense with many branches, normal incense
selling price: Liên hệ
Description
PEDAL INCENSE MAKING MACHINE
GENERAL INTRODUCTION OF PEDAL INCENSE MAKING MACHINE:
- How to create all the incense with the lowest cost, pedal incense making machine will be the good choice, who can invest in this machine: beginner and long time incense maker. Although it is a manual incense machine, many customers still prefer to use it because:
+ Low cost (suitable for starting a business, launching a sample of market exploration before mass production).
+ Compact design, easy to transport, weighing only 50kg. (This is a picture of incense machine after packaging it neatly)
+ Operation principle is extremely simple, anyone can do it. (insert pictures of working women and children )
+ Do a lot of sizes including twisted incense, flower-shaped incense, square incense ...
This pedal incense making machine can make incense sticks such as wormwood incense, perch incense, spiral incense, flower-shaped incense with many branches, normal incense, time incense and dragon incense (with time incense and dragon incense, you have to buy one press machine to create a new incense spiral, dragon and pattern carved on the incense). We only need to replace the perfum oil and the rocket to make the incense we want.
STRUCTURE:
- Structure foot pedal machine consists of 3 main parts:
1. The body (press body): includes detailed parts such as chain transmission, rubber gaskets, presser bar (stoppers), crisscross crank, stainless steel powder tube, push bar , jar of T-powder (inside are oils and rockets).
2. Table containing sticks and incense: trays containing incense, trays containing sticks, adjust the length of incense.
3. Tripod bracket: next to a tripod with pedals.
The body of the machine (the body) includes detailed parts such as chain transmission, rubber gaskets, presser bar (stopper), crisscross crank, stainless steel powder tube, push bar.
PRINCIPLES OF OPERATION:
- The pedal incense making machine is based on two chain drives and a set of moving gear rack.
- Before pedaling, we put the dough into the tube, we use the foot to pedal, the dough will be pressed into a jar of T, then the powder spit outward through the hole and carry a stick, forming an incense stick.
- Depending on whether the incense is large or small, long or short, we will step on the foot more or less. If you pedal a lot, the piston will squeeze down a lot. When we see the rubber cap is stopped, if we neglect to kick hard, we will break the gears, so we have to pay attention to this part.
- When we want to spin up, first we have to remove these two stoppers, use the hand to rotate in a clockwise direction, the piston will spin up, so we put the dough in.
INSTRUCTIONS OF USING MACHINE:
Before operating the pedal, we proceed to put the mold into the machine according to the following principle: First we put the rocket in first, so that the top of the rocket is equal to the output side, then turn the canopy right in so that just touched the bottom of the rocket.
Next, put the output end in the T-jar, then screw the left canopy tightly.
So basically we have pre-adjusted machine mold, we proceed to operate the machine.
To operate pedal incense making machine, we operate the following steps:
- Step 1: Put the mixed dough into flour tube, we fill the dough tube.
- Step 2: Use the hand to turn the handle to press the piston down, until it stops spinning.
- Step 3: Put the stick in and use your foot to pedal continuously to form the incense, then stop. This step is a bit difficult, before putting toothpicks into pedal to create incense, we have to check "if the powder has a needle hole" or not, so when we pedal to form an incense stick.
We check:
- Using continuous pedal, let the powder spray out. Hold the workpiece up: if the dough does not have a hole, turn the rivet right into half of the ring, then step on it again, check it again, if there is a hole then stop. Use the stick to poke holes for the rocket holes. Then put the stick in, pedal continuously until enough incense sticks, then stop.
- Constantly so, we put sticks on and then pedal, remember to pedal quickly so that when making an incense stick, it will not form kinks between the connecting segments.
- Note: When the hole is big, we back the canopy ½ steps to make the dough as small as possible, so the incense will be very firm and tight.
.jpg)
